Good luck with your future apartment customizations!
Usually it's just acting as a simple relay (on-off switch) so there's two physical wires.
I've got my Hive thermostat running great with various Bosch and Vaillant boilers. And it works great with HA.
Some newer boilers have 12V "smart" controls but still expose 230V "dumb" call for heating pins.
Vaillant has a proportional signal as well, and that thing in my old home was 30 years old... [1]
[1] https://www.mikrocontroller.net/topic/126250?page=single
The one in my apartment has a “feature” a lot of US thermostats now have, where you set four ordered times called wake, leave, return, and sleep and the temperature you want the space in each interval. I know very few people who actually live in a household where everyone wakes, leaves, returns, and sleeps on the same schedule every day.
I work from home and personally just want to set a temperature and have the space stay at that temperature indefinitely but this system requires that I tap through and enter the desired temperature four times, while confirming the four intervals.
I guess I’d be happier with a more programmable thermostat that I could set to behave like an old school dial thermostat.
Your use case is possible with that. Just set the standard program to 15°C, and activate the holiday set to whatever you need whenever you want. Configure it to go to 15°C at some sensible time in the evening, so it won't go on even if you forget it.
Nope! The smart learning feature was the biggest pain in the ass. You’d be sleeping during the day for a night shift, only to find yourself freezing because it decided no one was home.
Anyway, my ideal setup would be to install 'smart' thermostat taps on every radiator in the house, either manually turn them down when you're not in the room or have them automatically detect activity or open windows and adjust accordingly. But each one has the authority to trigger the central boiler if needs be, instead of only the master thermostat in the living room.
Regarding "what is better" from energy efficiency, I would prefer a system that "check it" because my guess is that it depends a lot based on the individual situation. I mean everybody is going crazy over "IA" but a couple of sensors and a system smart enough to adjust your usage based on your particular situation and preferences (like "eco", etc.) is an exception.
But of course, not really feasible in Atlanta or Phoenix. Nighttime temps are too warm.
In general, you should either run the heater or have your window open. Both at the same time is bad news for your energy bill.
I've heard this theory a lot too, but it doesn't match with physics. A warm house loses more energy than a cold house, due to a higher temperature difference allowing easier heat transfer. So in most homes, with radiators and high temperature CV, it's way more efficient to just turn it off when you gone.
One exception is when you have a very well insulated house, combined with floor heating and a very efficient, low temperature heat pump. In this case, it takes a lot of time for temperature to move in the house and it's already incredibly efficient.
The reasoning: when you heat up the house, then your boiler needs to produce constant high-temperature water. When you keep the house at the same temperature, then the boiler produces much lower temp water and it is more efficient.
Insulation also matters because if your house has outer insulation then it means that heat transfer from the house to the environment is mostly blocked, but cross-room heat transfer is likely not (through the walls). Therefore it is better to heat the whole house than heating just a couple of rooms because if you do the latter then you'll end up heating the whole house anyway but you're using less surface area (meaning you need higher flow temperatures, meaning less efficiency).
How does your boiler produce heat for your water in your scenario?
> Therefore it is better to heat the whole house than heating just a couple of rooms because if you do the latter then you'll end up heating the whole house anyway but you're using less surface area (meaning you need higher flow temperatures, meaning less efficiency).
Just model the other rooms as very weird wall to the outside.
This is only true if the heating happens quickly and the system is less efficient when heating quickly. Otherwise, this doesn't make sense from a physics standpoint. A temporarily lower temperature differential means less kWh of heat lost.
FWIW I run my heat pump intermittently and with locally-smart TRVs that get to call for heat centrally, and a weather compensation only flow temperature curve, and it WORKSFORME!
The losses are proportional to the temperature differential between outside and inside.
So you should have somewhat higher losses from the hotter air streams from the radiators passing the windows.
Dunno about magnitude though.
That's true if you completely stop heating. However if you lower the temperature by roughly 3.5C when you're not home, you'll be saving energy.
So you can for example program it to be 16C when you're out and 19C when you're in. You don't completely turn off heating indeed.
https://www.honeywellhome.com/us/en/products/air/thermostats...
As you go on to describe, there probably isn't one.
(use at your own risk of course)
> rpitx is a general radio frequency transmitter for Raspberry Pi which doesn't require any other hardware unless filter to avoid intererence. It can handle frequencies from 5 KHz up to 1500 MHz.
Wait, how does that work?
1.5GHz is a _lot_, I can't imagine this is done with bit-banging an I/O line, nor do I expect the Pi will have a DAC with anything close to a 3GHz+ sample rate.
> Plug a wire on GPIO 4, means Pin 7 of the GPIO header (header P1). This acts as the antenna.
A bit of Googling shows me that on the later Pi board GPIO4 (pin 7) has a bunch of alternative modes, amongst which is a general purpose clock output (GPCLK0), a DPI output bit (DPI_D0) and what I recon is composite analog video in/out (AVEOUT_VID0, AVEIN_VID0), and the TDI JTAG pin. But none of these would get close to 1.5Ghz TRX capabilities, no?
What's the magic here?
Speaking of newish natural gas (CH4) heaters, they all should have modulating thermostat capability with OpenTherm/eBus or other protocol. Combined with a thermostat with outdoor temperature sensor system efficiency is increased a few percent and that should help offset thermostat and installation costs. In the end you have more efficient modern heating system.
Same should apply for heat pump systems.
If your goal is saving energy/money, you don’t want a system capable of going from cool to toasty in 20 minutes.
Instead, you want a system that runs (much) lower water circulation temperatures (giving lower losses in the unconditioned spaces and more even room heating). That can be done to any condensing boiler by just turning down the flow target temperature.
A second layer of optimization on top of this is the addition of outdoor reset/weather compensation which will adjust that flow temperature based on the outside temperature, giving a flow temperature than can just barely restore the building to the desired setpoint temp.
With mine properly tuned, I was targeting having the thermostat act more like a high-limit and for it to call for heat between 22 and 24 hours per day while not overheating the house. That often meant flow temps in the 110°F (warm day) to 135°F (below freezing day) range. Compared to the prior winter (at a constant 160°F flow), the house used 8-15% less gas and was wildly more comfortable. (This setup does preclude using deep setback settings, which also can save money, because recovery times are necessarily long in such a scheme, unless you have an even smarter control system that can run perfectly tuned water most times but hotter water during recovery from setbacks.)
I target the long run time to maximize efficiency. A 160°F pipe will lose more heat to the part of the building that I don’t want to heat as well as more heat to the wall right behind the radiators. It also results in the house going micro too-hot, too-cold, too-hot, too-cold as it cycles. Mine is constantly trickling in just enough heat to replace the heat lost instead of cycling between adding way more than needed then none for a while.
Another large effect is that low return water temperatures into the boiler allow for greater condensation of exhaust gas energy to be used in the building instead of sent outside. Walking by my house on a cold day, you’ll see minimal steam plume during operation. All that steam I see my neighbors emitting is energy they paid for and delivered to the outside… (They paid a lot for a boiler with a 95% or 98% sticker and run it at 80% efficiency.)
https://kw-engineering.com/how-to-optimize-condensing-boiler...
You’ve got the first part of that backwards, it’s the walls near your radiators that are your problem and need more insulation.
The other variable is how well controlled your heating is. A lower flow temperature means less overshoot of the target set point - and as losses scale linearly with temperature delta, that can mean higher energy losses (depending on the characteristics of the controller of course).
Whether or not you care about losses in unheated spaces depends on your system topology. Personally, all my heating pipes are within the thermal envelope of my house, so flow temperature has no bearing on those losses at all.
If you had a resistive electric boiler, flow temperature would have absolutely no effect on efficiency. You'd be completely right, that running heating only when you needed it would be more energy efficient.
Energy moves from hot to cold linearly with temperature differences. Hypothetically, if the pipe was the same temperatures as the inside of your home all the heat transferred would be outside the envelope. The hotter the pipe the better this ratio becomes. This is true regardless of what percentage of the pipe is inside the envelope.
However, heating along the exterior of the home under windows and such then you’ll heat the exterior walls to higher temperatures than the interior thermostat thus losing more heat to the outside. Radiant heating on the other hand largely avoids this effect.
(not a native speaker here)
Depends. As explained in a sibling comments, I have some rooms that have combined UFH and radiators, and if the desired temp is more than 1 celsius away from the current temp, then both are driven, otherwise it's just the UFH.
So long as you can get the boiler return water temps low enough, you can operate the boiler in its high efficiency range.
Most dual-temp setups are set for the highest temp and mixed-down to provide the lower temp for under-floor. That’s cheapest in terms of equipment and install but cannot be as efficient as a system that mixes down when both loads call but also lowers flow temp (thereby lowering return temp) when no high-temp rads are calling.
The original product understandably arrives with heavily-restricted firmware (I imagine to reduce the amount of flak the company receives). However, it is incredibly easy to install Flipper Unleashed or similar, which removes all said restrictions and adds a lot of additional functionality.
Possessing the tools that could be used to commit a crime is not necessarily a crime in and of itself! Just be careful with what you do or, depending on what country you’re in, you might find some men in suits knocking at your door.
Personally, I wanted to replay “encrypted” 433MHz signals for my own devices (electric gate, roller door, roller shutters, …) and this was disabled with the Flipper’s region set to Australia.
While I do agree 1000%, I also want people to be careful with this thinking since I have gotten in some minor trouble in the past. Always assume the authority questioning you can and will create whatever narrative they wish, that it will be accepted, and that your own reasoning will likely be used against you.
I will always encourage exploration and curiosity in tech, but if we stick with the Flipper Zero example, there's a few things one should keep in mind, regardless of the jurisdiction they're in:
* Don't carry it around unless you intend to use it.
* Read all documentation before you start practicing, then practice being subtle.
* Taking a note from my outdoorsy side, adopt the "leave no trace" ethos.
* Pay attention to the effect your presence and actions have on the environment and your target and how that might be interpreted by an outside observer, then take action to mitigate suspicion.
These apply to lots of devices, everything from your disposable smartphone to a cheap RFID card copier from Temu.
Our eagerness sometimes gets the best of us, especially new-comers, and we want to jump to the part where we can be like the hackers we see in tv and video games. There's a reason those guys are fictional characters. Innocuous actions or not, the perception of the authority questioning you is all that will matter, in the end.
In particular: stable and individually adjustable temperatures for bedrooms and living rooms; underfloor heating in some rooms (bedrooms), radiator-based heating in some others (living room), and combined UFH+radiators in some others (where UFH might not be enough during extreme colds).
I thought I can just pay someone some money and they'll set up the controls for me. It must be a simple exercise, right?
I could not have been more wrong. After spending a few hours of understanding the setups that "experts" have recommended, I figured out edge cases where they would be either wasteful or uncomfortable (meaning: unnecessary and inavoidable temperature overshoots or undershoots, etc.). I had many-many rounds with Honeywell, Tado, Siemens, etc. and every single one of them had _major_ issues.
The renovation got a bit stuck because of this, but the plumbing was ready so I wanted to see whether the pluming and pumps are working, at least. So I connected the pumps and valves to "smart plugs", i.e. Zigbee-controlled plugs, so that I can see that they turn on. They did, which got me thinking...
Right now I have $20 Zigbee temp sensors sprinkled across the house, $30 smart plugs and relays driving valves, pumps and the boiler, and Home Assistant is controlling the whole thing. Everything works perfectly and I could implement some features that simply no system would have done out of the box, for example in rooms where there's combined UFH and radiators I can drive both heating systems when the target temperature is far from the desired (so that the room heats up quickly) but as the room temp is getting closer to the target, the radiators are turned off so that UFH dominates heating (more comfortable and more energy efficient than radiators). In rooms with radiators, temp is +- 0.4 C within target, in rooms with UFH, it's +-0.1C within target.
Some people are unlucky enough to buy homes where a machine engineer designed the boiler setup and the boiler room have enough valves and manometers to like operate the engine of Titanic.
I guess programmers are the new sinners in this area nowadays.
If I inherit a heating system I want it to be all mechanical except maybe the control system for any heating pump.
(But still more comfortable than 99% of the houses I've been in.)
I haven't mentioned in the parent comment but as a test I've dismantled the HA system and installed the Siemens system and it works well, just not 'perfectly'.
In generall I think all these IoT systems will be a major headache as they age.
My thermostats on the radiators are 45 year old by now. That is kinda the expected service life we are used to.
My knowledge is that for UFH you run at temps between 40-50C and radiators run at 60-70*C.
Almost everything in engineering is like this, not just heating. It's pretty rare that something is fully optimised.
A hammerier solution would be to control the temperature seen by the thermostat (ignore the difficult RF protocol).
A heating element and a temperature reading could control the heat seen by the thermostat.
I'm pretty sure you wouldn't need any cooling (Peltier or whatever). Just a heater and ambient cooling! Set the thermostat to a high temperature, and run the heater to make the measured temperature hotter: when you don't want the heating to run.
That said, I think hacking the RF protocol is geekier and far awesomer.
It seems like the easier hack would be to put a peltier heater/cooler under the thermostat then control that remotely to assume control over what temperature the thermostat sees.
The link to the exact model of thermostat isn't working, so I don't know how amenable its design is to this approach, but the thermostats I've used are generally wall-mounted and putting a heat/cool source under them wouldn't be too hard. You'd need to make sure that you didn't send both the heat and cool into the thermostat, but that's a simple positioning problem.
All the apartments I lived in had basic thermostats; and I even rewired and replaced one of them.
What was blocking Videah from buying an off-the-shelf thermostat?
Then the boiler is basically controlled by the relay.
The government maintains indoor temperature at 24 degrees from October to May, and the water is heated at the power stations.
willvarfar•7h ago
kbuck•6h ago
unsnap_biceps•6h ago
mschuster91•5h ago
avidiax•6h ago
That said, if he has access to the interior of the thermostat, I'm sure it won't be difficult to replace the temperature sensor with a circuit to cause it to read either really high or really low on demand.
toast0•6h ago
Ice pack and desiccant?
willvarfar•5h ago
dtech•5h ago
mjlee•6h ago
Probably a 30 minute job if you’ve never done it before and easily reversible with a little bit of double sided sticky tape, which all Brits should be familiar with if they ever made a Tracy Island. There is a real risk of electrocution which could be completely militated against by turning off the power to the boiler.
Still, a fun hack, and nicely executed!
haileys•6h ago
nippoo•5h ago
anal_reactor•5h ago
Gazoche•3h ago